Pool Plaster vs Pebble Finish for Killeen Pools

Straight answer on pool plaster vs pebble finish: plaster is cheaper up front and lasts 7 to 12 years, pebble costs roughly double and lasts 15 to 20. If you plan to own the pool through the next replaster cycle, pebble is the better math. If you might sell inside five years, white plaster and a nicer deck will do more for you.

Now the part the plaster crew tells you in the driveway and nobody puts on a website: every interior finish in the world is a sacrificial layer. It is cement holding stone, sitting in water that is chemically trying to dissolve it. Your job is picking how thick and how stubborn that layer is.

The three finishes you are actually choosing between

Finish	What it is	Typical life	Typical installed cost, 16x32 pool
White plaster (marcite)	White portland cement + crushed marble dust	7–12 years	$4,500–$7,000
Quartz aggregate	Cement + crushed quartz (Diamond Brite, Krystalkrete)	10–15 years	$6,000–$9,500
Pebble	Cement + river pebble, exposed by washing (Pebble Tec, StoneScapes)	15–20+ years	$8,000–$14,000

Those are interior-surface jobs including chip-out, waterline tile, and start-up. A deeper pool, a spa spillover, or a backyard your crew has to wheelbarrow through changes the number.

Plaster: the honest budget pick that gets unfairly trashed

White plaster has been the default pool interior since the 1950s for a reason. It is smooth, it is bright, it makes the water that classic blue, and it is the cheapest way to make a tired pool look new.

Its weaknesses are real though. It stains. Leaves, metals in the fill water, and a summer of neglected chemistry leave marks that never fully scrub out. And it is soft enough that aggressive water etches it — run your pH under 7.2 or let calcium hardness drop below about 200 ppm and you are chemically sandblasting your own pool.

You get maybe two or three acid washes out of a plaster surface in its life. Each one strips a thin layer to reveal clean material underneath. It works. It also brings the funeral closer every time.

Pebble: buy it for the years, not the looks

Pebble finishes embed small river stones in the cement matrix and then wash the surface so the stone sits proud. That exposed aggregate is the whole trick — a stain has nowhere flat to sit, and the surface has far more material to give up before it fails.

Two honest downsides. First, texture. Classic large-pebble finishes are genuinely rough, and the place you notice is the tanning ledge where a five-year-old parks for three hours. Polished pebble products grind the stone down and solve most of this, at a price.

Second, algae. All that texture is more surface area, so a pebble pool that goes green punishes you harder during cleanup. Not a dealbreaker, just a thing.

What actually kills a finish (it is not the finish)

Here is the part that decides more than the product choice: water chemistry, measured against the Langelier Saturation Index. Cement finishes want water that is slightly scale-forming, not slightly hungry.

Keep it in these lanes and any of the three lasts near the top of its range:

• pH: 7.4 to 7.6
• Total alkalinity: 80 to 120 ppm
• Calcium hardness: 200 to 400 ppm
• Cyanuric acid: 30 to 50 ppm in a sunny climate like Bell and Coryell counties

The first 28 days matter most. New plaster is still curing, and the start-up brushing schedule — twice a day for the first week or two, no salt for the first 30 days on a saltwater conversion — is not optional busywork. Skipping it is how a brand new $9,000 surface gets a mottled gray blotch that no chemical ever removes.

When you should not resurface at all

We would rather say this than sell you a job you do not need.

If the surface is stained but still smooth, do not resurface. Run your palm along the wall at the shallow end. If it feels like a dinner plate, you have plaster left. A proper drain-and-acid-wash usually runs $400 to $800 and buys another two to four seasons. Spending $9,000 to fix a color problem is a bad trade.

Resurface when you feel it, not when you see it. Rough enough to scrape a knee, exposed gray patches, plaster popping off in nickel-sized chips, or a floor that eats your pool vacuum — that is a structural conversation, not cosmetic.

The call we get every spring

The 1990s pool. Still holds water, pump still runs, but the plaster is the color of weak coffee and the owner has spent three seasons attacking it with a brush and a bottle of stain remover. They ask us to make it white again.

Sometimes an acid wash does it and everybody is happy for $600. About half the time the plaster is already thin enough that a wash would eat through, and the honest answer is that the surface is done. Both answers take ten minutes to reach with a hand on the wall. Neither one requires a sales pitch.

Our actual recommendation

Go pebble if you will own the pool past the next 10 years, and pick a polished pebble if you have young kids. The lifespan difference — call it 17 years against 9 — means pebble's higher price works out to about the same annual cost, and you skip an entire drain-refill-and-two-weeks-of-hassle cycle along the way.

Go white plaster if you are selling within five years, or if the budget is tight and you would rather put the difference into decking and coping, which is what guests actually look at.

Go quartz if you want color that holds without pebble money. It is the pick most people are happiest with a decade later.

Whichever way you land, the interior is also the only time the pool is empty — so it is the cheapest moment to add a remodel item like new waterline tile, a raised bond beam, or a spa. Doing that later means draining it again.

Killeen Pool Builders handles pool resurfacing across Killeen and Bell and Coryell counties in plaster, quartz, and pebble, and we will tell you when a $600 acid wash beats a $9,000 job. If you want the numbers for your specific pool, see our pool resurfacing cost breakdown or call (844) 511-2320.

Get a free quote → · call (844) 511-2320